PLUMBING BASICS: THE FIRST STEP FOR BATHTUB INSTALLATION

Plumbing Basics: The First Step for Bathtub Installation

Plumbing Basics: The First Step for Bathtub Installation

Blog Article

View Website

Were you looking for answers concerning A Step-by-Step Guide to Installing a Bathtub?


Tools You Need to Install a New Bathtub
Mounting a tub isn't precisely rocket science, but it does call for strong plumbing, woodworking, as well as often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging job. If the old bathtub is conveniently easily accessible, the job can relocate immediately; if you need to open up a wall to eliminate the old tub and also position the brand-new bathtub, the job is much harder. In either case, the job is within a residence handyman's abilities, although you will require an assistant to move out the old tub and set in the new one. Ensure you have qualified yourself for the job and also are comfortable attempting it. Rather than employing a contractor to take control of a halfway-completed project, it is much better to consider employing one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will help you mount a brand-new bathtub in your shower room if you have actually currently bought a new tub as well as do not need to transform the setup of your previous supply of water pipes.
Your devices as well as material checklist ought to make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Preparing for the Installment


    Firstly, the sustaining frame provided with the bath must be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop strain on the bathtub.
    Fit the flexible tap connectors to the bottom of the two taps using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of all of the provided washing machines.
    Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its last position.

    Removing Old Touches


    If you need to replace old taps with new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, turn on the taps to drain any water staying in the system. The procedure of eliminating the existing faucets can be rather troublesome as a result of the limited accessibility that is often the instance.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipelines. Once the supply pipes have been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
    Prior to moving on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Mounting the Bath tub


    Making use of both wood boards under its feet, position the bath tub in the called for position. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small points.
    The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bathtub till the level checks out level.
    To mount taps, fit all-time low of the outermost flexible faucet connector to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
    Switch on the water supply and also check all joints and also new pipework for leaks as well as tighten them if essential. Fill the bath tub and likewise check the overflow outlet as well as the normal outlet for leakages.
    Finally, repair the bathroom paneling as described in the maker's user's manual. Tiling and securing around the bath tub should wait until the tub has actually been made use of at the very least once as this will settle it into its final setting.

    Suitable New Touches


    If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end gives a link to the current supply pipelines.
    If you need to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
    Next, place the tap in the mounting opening in the bath/basin ensuring that the washing machines are in place between the tap and also the sink. Secure the faucet in position with the supplier provided backnut. When the tap is safely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal tap ports. The previous type must be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Bathtub


    In the area where the bathroom satisfies the tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to fracture a stiff seal, causing the water to pass through the wall surface between the bathroom and the tiling, leading to difficulties with wetness and possible leakages to the ceiling listed below.
    You can choose from a variety of coloured sealers to blend in your components as well as fittings. They are sold in tubes and cartridges, and are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can split relatively early if you do not take into consideration this movement before sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles using waterproof or water resistant adhesive as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    As a passionate reader about How to Install a Bathtub Yourself, I thought sharing that excerpt was sensible. Are you aware of somebody who is inquisitive about the niche? Do not hesitate to promote it. Thanks for going through it.


    Secure fix? Ring!

    Report this page